Citizen CBM-910 Type II Manual de instrucciones Pagina 79
- Pagina / 114
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 5 mV Measurement
F-72 67
5.6 mV Measurement
This section describes the procedures of mV measurement.
1. Wash the electrode with pure water (ion
exchange water), and wipe it off either with filter
paper or tissue paper.
2. Open the internal solution filler port of the
electrode.
During measurement, the filler port should be
kept open.
The filler port configuration depends on the
electrode type.
3. Immerse the electrode into the sample solution
deeper than 3 cm from the tip.
Immerse the electrode tip at least 3 cm into the
sample solution for an accurate measurement.
Refer to the instruction manual of the electrode for
more details.
4. Press the MEAS key, and tap the channel
setting and the measurement item in the MEAS
screen to set "CH1" and "mV".
Tap to convert the potential display
between ABS (absolute potential) and REL
(relative potential).
Tapping shifts the measured potential to
zero, and displays the difference in relative
potential.
The potential without correction is called
"absolute potential."
5. Tap to start measurement.
The measurement value is displayed, and the
HOLD indicator blinks until the reading
stabilizes.
To stop calibration tap while the HOLD
indicator blinks.
When the reading stabilizes, the value is held
and HOLD indicator lights up.
During instantaneous value measurement, or
when a measurement value is held, you can
store the measurement values by tapping on
the bottom of the screen.
6. After the measurement is completed, tap
to proceed to the next measurement.
- Instruction Manual 1
- ■ Preface 2
- ■ Warranty and Responsibility 2
- ■ Trademarks 2
- Operation Manual 2
- ■ Conformable Directive 3
- ■ FCC Rules 4
- SAFETY OPERATION 5
- ■ Safety Precautions 6
- ■ Description in This Manual 8
- Contents 10
- Chapter 1 OVERVIEW 13
- 1.1.3 Left Side 14
- 1.1.4 Right Side 14
- 1.1.5 Accessories 14
- 1.1.6 Operation Keys 15
- 1.1.7 Icons (Icon Bar) 16
- 1.1.8 Status Icons 17
- 1.1.9 Meas Screen 18
- 10 HORIBA 22
- 12 HORIBA 24
- 1.6 Connecting the Electrode 24
- 1.8 Connecting the Printer 25
- 14 HORIBA 26
- 1.10 Turn ON the Power 27
- 16 HORIBA 28
- 2.1 Meter SET Screen 28
- 2.2 Auto Hold Setting 28
- 2.3 Custom Setting 29
- 18 HORIBA 30
- 2.4 Sample Name Setting 30
- 2.5 Interval Memory Setting 31
- 20 HORIBA 32
- 2.6 USB Memory Setting 32
- 22 HORIBA 34
- 2.7 Printer Setting 34
- (Not be omitted) 35
- 24 HORIBA 36
- 2.8 Screen Settings 36
- 26 HORIBA 38
- 2.9 Sound Setting 38
- 2.10 Language Setting 39
- 2.11 Security Setting 39
- 28 HORIBA 40
- 30 HORIBA 42
- 2.13 Date Setting 43
- 32 HORIBA 44
- 2.14 Analog Output Adjustment 44
- 34 HORIBA 46
- Chapter 3 pH Measurement 47
- 36 HORIBA 48
- 3.1.4 Checking Before Use 49
- 2. Tap 49
- 38 HORIBA 50
- 3.2 pH Calibration 50
- 40 HORIBA 52
- 3.3 Checking Before Use 53
- 42 HORIBA 54
- 3.5 pH Measurement Setting 55
- 44 HORIBA 56
- 46 HORIBA 58
- 3.9 Alarm Setting 58
- 3.10 Electrode Model Setting 59
- 48 HORIBA 60
- 3.12 pH Measurement 61
- Chapter 4 ION Measurement 62
- 4.1.2 Checking Before Use 63
- 52 HORIBA 64
- 4.2 ION Calibration 64
- 54 HORIBA 66
- 4.3 Checking Before Use 66
- 4.4 ION Measurement Setting 67
- 56 HORIBA 68
- 4.7 Alarm Setting 69
- 58 HORIBA 70
- 4.8 Electrode Model Setting 71
- 60 HORIBA 72
- 4.9 Electrode Lot No. Setting 72
- 4.10 ION Measurement 73
- Chapter 5 mV Measurement 74
- 5.3 Alarm Setting 75
- 64 HORIBA 76
- 5.4 Electrode Model Setting 77
- 66 HORIBA 78
- 5.5 Electrode Lot No. Setting 78
- 5.6 mV Measurement 79
- Chapter 6 ORP Measurement 80
- 6.2 ORP Measurement Setting 81
- 6.3 Temperature Setting 81
- 70 HORIBA 82
- 6.4 Alarm Setting 82
- 6.5 Electrode Model Setting 83
- 72 HORIBA 84
- 6.6 Electrode Lot No. Setting 84
- 6.7 ORP Measurement 85
- Chapter 7 Application Mode 86
- 76 HORIBA 88
- 78 HORIBA 90
- 80 HORIBA 92
- 8.1.1 Settings 93
- 82 HORIBA 94
- 84 HORIBA 96
- 8.1.4 Simulator (X-51) Mode 97
- 86 HORIBA 98
- 88 HORIBA 100
- 8.3 Comment Input 100
- Chapter 9 Data 101
- 90 HORIBA 102
- 9.3 Measurement data_latest50 102
- 9.4 Measured data_Search 102
- 9.6 Copy all Meas. Data 103
- 9.5 Cal. results_All 103
- 92 HORIBA 104
- 9.7 Delete all meas. Data 104
- 9.8 Delete all cal. data 104
- Chapter 10 Specifications 105
- 94 HORIBA 106
- 10.2 Default Settings 106
- (Can be set per operator) 107
- 96 HORIBA 108
- 98 HORIBA 110
- 10.3 Options 111
- 1st edition: October 2011 113
- CODE: GZ0000260894 113
- 表紙は別途デザインの表紙とする 114
Relacionado con productos y manuales para Impresión y escaneo Citizen CBM-910 Type II
Impresión y escaneo Citizen CT-S280 Especificaciones
(156 paginas)
(156 paginas)
Impresión y escaneo Citizen 3541 Manual de usuario
(21 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales