Citizen CMP-30 series Manual de usuario Pagina 1

CMP-30 CPCL Command Manual Rev 1.0 2009.4.1

10CMP-30 Command Manual 3. TEXT A. TEXT Commands The TEXT command is used to place text on a label. This command and its variants control the spec

11CMP-30 Command Manual B. FONT-GROUP(FG) Command The FG command gives a user the ability to group up to 10 pre-scaled font files into a single gro

12CMP-30 Command Manual C. TEXT CONCATENATION Command Text concatenation allows you to assign different character styles to strings, printing them

13CMP-30 Command Manual D. MULTILINE(ML) Command MULTILINE (ML) allow you to print multiple lines of text using the same number of font and line-he

14CMP-30 Command Manual E. COUNT Command The COUNT command is used for printing multiple labels where a numeric text field or numeric data encoded

15CMP-30 Command Manual 4. Linear Bar Codes A. BARCODE Command The BARCODE command prints bar codes in both vertical and horizontal orientations a

16CMP-30 Command Manual B. BARCODE-TEXT Command The BARCODE-TEXT command is used to label bar codes with the same data used to create the bar cod

17CMP-30 Command Manual 5. Two-Dimensional Bar Codes A. PDF417 (PORTABLE DATA FILE) The following commands are used for the creation and formattin

18CMP-30 Command Manual B. MAXICODE This revision supports only Mode 2 bar codes. Format {command} {type} {x} {y} {tag} {options} … {tag} {options}

19CMP-30 Command Manual HEAD Transportation data format header 01[GS]98 TN Tracking Number [GS] SCAC Standard Carrier Alpha Code UPSN SHIPPER UP

2CMP-30 Command Manual TABLE OF CONTENTS 1. Programming Introduction 5 2. Printer Commands 6 A. Printer Commands B. PRINT Command C. FORM Command

20CMP-30 Command Manual 6. Graphics A. BOX Command The BOX command provides the user with the ability to produce rectangular shapes of specified l

21CMP-30 Command Manual C. INVERSE-LINE Commands The INVERSE-LINE Command has the same syntax as the LINE command. Previously created objects that

22CMP-30 Command Manual E. GRAPHICS Commands Bit- mapped graphics can be printed by using graphics commands. ASCii HEX is used for expanded graphi

23CMP-30 Command Manual F. PCX Commands The PCX command gives a user the ability to send “.PCX” graphics formatted images to the printer. The .PCX

24CMP-30 Command Manual 7. Advanced Commands A. CONTRAST Command The contrast command is used to specify the print darkness for the entire label.

25CMP-30 Command Manual D. PAGE-WIDTH Command The command specifies the page width Format {command} {width} Command & option {command} PAGE-W

26CMP-30 Command Manual E. PACE Command When PACE is activated, the user must depress the printer’s ‘FEED’ key to print additional labels until the

27CMP-30 Command Manual H. SPEED Command This SPEED command selects a speed level within a range of 0 to 5, with 0the slowest speed. Format {comman

28CMP-30 Command Manual K. ON-FEED Command Your printer can be configured to ignore, form-feed, or reprint the last label when the feed key is pres

29CMP-30 Command Manual M. POSTFEED Command The POSTFEED command instructs the printer to advance the media a specified amount after printing. Form

3CMP-30 Command Manual 7. Advanced Commands 24 A. CONTRAST Command B. TONE Command C. JUSTIFICATION Commands D. PAGE-WIDTH Command E. PACE Command

30CMP-30 Command Manual O. USING FORMAT FILES When you used the same form repeatedly, you can print the label only sending variable date to the pri

31CMP-30 Command Manual 8. Line Print Mode The “! UTILITIES” command, or “! U” for short, must be ended by the terminator “PRINT” followed by a CR/

32CMP-30 Command Manual C. Moving With X and Y Coordinates Even though the printer is in a line print mode, it can still move down and across the p

33CMP-30 Command Manual G. PAGE-WIDTH Command This command let you control the width. Format ! U1 PW {unit width} {unit width} Printing width for

34CMP-30 Command Manual K. SET-TOF Command This command is used to program the distance between the top-of-form and the end of the next or previous

35CMP-30 Command Manual 9. Advanced Utilities A. VERSION Utility This command reports the firmware version as a four character null-terminated ASC

36CMP-30 Command Manual E. DEFINE-FILE(DF) Utility The DF command defiles a file name for a file to be loaded into the printer. If a file with the

37CMP-30 Command Manual H. TIMEOUT Utility If no data is received after the specified timeout, the printer will turn itself off to save energy and

38CMP-30 Command Manual K. SET-TIME Utility This command sets the time in the real time clock module. Format <!> <UTILITIES> {command}

39CMP-30 Command Manual N. GET-DATE Utility This command reports the current date. Format <!> <UTILITIES> {command} <PRINT> Comma

4CMP-30 Command Manual 9. Advanced Utilities 35 A. VERSION Utility B. CHECKSUM Utility C. DEL Utility D. DIR Utility E. DEFINE-FILE(DF) Utility F.

40CMP-30 Command Manual Q. PAPER-JAM Utility This command establishes the parameters that allow the printer to report a paper jam. Format <!>

41CMP-30 Command Manual 10. Printer Escape Commands A. SET AND READ CODE Command Printer command sessions normally start with the ‘!’ character. Wh

42CMP-30 Command Manual 2. Get Printer Information ESC (0x1b) ‘s’(0x73) This command instruct the printer to return a null-terminated string contai

43CMP-30 Command Manual 11. Configuration/Control Commands The following section covers a set of commands to configure and query printer parameters

44CMP-30 Command Manual characters “setpin”. This parameter is not used when the “bluetooth.authentication” parameter is set to “default” or “off”.

45CMP-30 Command Manual printer files. file.rename do This command can be used to rename printer files. file.run do This command can be used to

46CMP-30 Command Manual “journal”  default “label” Memory Parameters memory.flash_size getvar This parameter refers to the total amount of F

47CMP-30 Command Manual setvar “0” ~ “65535” the printer reaches the low battery state this timeout will become active. The printer will shut down a

48CMP-30 Command Manual GAP-SENSE & BAR-SENSE Commands These commands are used to instruct the printer as to which means of top-of-form detectio

5CMP-30 Command Manual 1. Programming introduction This manual details the various commands in the CPCL language which allow the programmer to uti

6CMP-30 Command Manual 2. Printer commands A label file always begins with the “!” character followed by an “x” offset parameter, “x” and “y” axis

7CMP-30 Command Manual B. Print command The print command terminates and prints the file. This must always be the last command (except when in Line

8CMP-30 Command Manual E. UNITS Command The Units commands are used to specify a measurement system for all subsequent command fields in a control

9CMP-30 Command Manual F. Using Comments Comments can be added between the first line of a command start line and the print command. A comment is p